塑料模具設計技術英語

Chapter l General mould construction基本模具結構
1.1 Basic Terminology基本術語
1.2 Integer cavity and core plates整體式型腔和型芯板
1.3 Use of local inserts局部鑲塊的使用
1.4 Inserts for cavity and core型腔和型芯鑲塊
1.5 Types of guide pillars and guide bushes導柱和導套的形式
1.6 Sprue bush澆口套
1.7 Register rin9定位圈
Chapter 2 Parting surface分型面
2.1 Flat parting surface平面分型面
2.2 Non—flat parting surface非平面分型面
2.3 Relief of parting surfaces分型面的釋放
2.4 Ventin9排氣
Chapter 3 Ejection system頂料系統
3.1 Removing the moldin9塑件的取出
3.2 In—line Ejector grid內嵌頂料架
3.3 Ejector plate assembly頂料板組合
3.4 Ejector plate頂料板
3.5 Retaining plate and stop pins固定板和擋釘
3.6 Ejector plate assembly returns systems頂料板回程機構
3.7 Ejection Techniques頂料方法
3.8 Pin ejection頂桿頂料
3.9 Stepped ejector pins階梯形頂桿
3.10 Sleeve ejection頂管頂料
3.11 Stripper plate ejection頂板頂料
3.12 Sprue pullers主流道拉料桿
3.13 The B sprue pullers B型主流道拉料桿
Chapter 4 Feed system澆注系統
4.1 Runner分流道
4.2 Runner cross section shape分流道截面形狀
4.3 Runner size分流道尺寸
4.4 Runner layout分流道布置
4.5 Gates澆口
4.6 Positioning of gate澆口的位置
4.7 Sprue gate主流道型澆口
4.8 Rectangular edge gate矩形澆口
4.9 Round edge gate圓澆口
4.10 0verlap gate疊合式澆口
4.11 Fan gate扇形澆口
4.12 Tab gate護耳式澆口
4.13 Diaphragm gate疊合式膜狀澆口
4.14 Ring gate and film gate環形澆口和膜狀澆口
4.15 Pin gate點澆口
4.16 Subsurface gate潛伏式澆口
4.17 Winkle gate螺肉形澆口
Chapter 5 Mould temperature control模具溫度控制
5.1 Mould coolin9模具冷卻
5.2 The cooling of shallow integer type cavity整體式淺腔的冷卻
5.3 The cooling of deep integer type cavities整體式深腔的冷卻
5.4 Cooling integer type core plate整體式型芯板的冷卻
5.5 Cooling insert bolster鑲塊板的冷卻
5.6 Cooling rectangular cavity inserts矩形型腔鑲塊的冷卻
5.7 Cooling circular cavity inserts圓形型腔鑲塊的冷卻
5.8 Cooling shallow core inserts淺型芯鑲塊的冷卻
5.9 Cooling deep core inserts深型芯鑲塊的冷卻
5.10 The helical cooling channel design of deep core insert深型芯鑲塊的螺旋冷卻槽設計
5.11 Baffled hole system design of deep core insert深型芯鑲塊帶隔板孔的冷卻系統
5.12 Heat rods of deep core insert coolin9深型芯冷卻用的熱桿
5.13 Heat pipe of deep core insert coolin9深型芯冷卻用的熱管
5.14 Cooling of valve ejectors and sprue bush閥形頂桿和主流道襯套等的冷卻
……
Chapter 6 Standard parts systems模具標準件系統
Chapter 7 Purchasing order模具采購合同
Chapter 8 Mould design technology documents模具設計技術文本
References參考文獻